Discover the Power of Durability, Stability and Precision From Akuracy , a brand fully owned by Ratnakar Enterprises Jointly With Balaji Industries.

We offer high-quality products with unbeatable Innovative technologies and flexibility.

Our commitment to excellence is unmatched. Enjoy the benefits of our top-notch products today!

8.8 Grade Bolt Testing: Tensile Strength, Proof Load and Hardness

Akuracy hydraulic grips universal testing machine used for tensile and proof load testing of 8.8 grade bolts

Ameet Kudche |

Short answer: an 8.8 grade bolt is a property class defined in ISO 898-1 (IS 1367 Part 3 is the Indian counterpart). The first "8" means a nominal tensile strength of 800 MPa. The ".8" means the nominal yield strength is 80% of that, or 640 MPa. To confirm a batch really is 8.8, a fastener QC lab normally runs three checks: a full-size tensile test, a proof load test and a hardness test. A universal testing machine (UTM) handles the first two and a Rockwell or Vickers hardness tester handles the third.

Akuracy hydraulic grips universal testing machine used for tensile and proof load testing of 8.8 grade bolts

What does 8.8 mean on a bolt head?

The marking on the head is shorthand for two numbers:

  • First number (8): nominal tensile strength ÷ 100. 8 × 100 = 800 MPa.
  • Second number (.8): ratio of nominal yield strength to nominal tensile strength. 0.8 × 800 = 640 MPa.

These are nominal values used for the designation. The minimum values a bolt must actually meet depend on its diameter, and they come from the tables in ISO 898-1.

Key mechanical requirements for class 8.8 (ISO 898-1)

Class 8.8 is split at 16 mm nominal diameter. Larger bolts get slightly higher minimums. The table summarises the values most labs check, based on ISO 898-1:2013. Always confirm against the edition named on your purchase order or drawing.

Property d ≤ 16 mm d > 16 mm
Tensile strength Rm, min 800 MPa 830 MPa
0.2% proof strength Rp0.2, min 640 MPa 660 MPa
Proof stress Sp 580 MPa 600 MPa
Vickers hardness 250–320 HV 255–335 HV
Rockwell hardness 22–32 HRC 23–34 HRC

The three core tests for 8.8 bolts

1. Tensile test on the full-size bolt

The bolt is pulled to fracture in a UTM using threaded adapters or a nut-and-fixture setup. For full-size bolts, the standard also uses a wedge under the head, which checks the head-to-shank junction under an angled load. The minimum breaking load is the minimum tensile strength multiplied by the nominal stress area (As) of the thread.

Worked example (M12 coarse thread): As = 84.3 mm². Minimum ultimate tensile load = 800 MPa × 84.3 mm² = 67,440 N, about 67.4 kN. For the bolt to pass, fracture should occur in the shank or the free threaded length, not at the junction of the head and shank.

2. Proof load test

The proof load is the force a bolt must carry without measurable permanent stretch. It is calculated as Fp = Sp × As.

Worked example (M12, class 8.8): 580 MPa × 84.3 mm² = 48,894 N, which the ISO 898-1 table rounds to 48,900 N (about 48.9 kN).

The procedure in short:

  1. Measure the bolt length precisely before loading.
  2. Apply the proof load axially and hold it for the dwell time the standard specifies.
  3. Unload, then measure the length again.
  4. The bolt passes if the length change stays within the measurement tolerance the standard allows.

Good load control matters here. Overshooting the proof load can stretch a sound bolt, and that becomes a false failure.

3. Hardness test

Hardness confirms that the heat treatment (quench and temper) did its job. Labs usually test on a cross-section at a defined position in the thread area, using Rockwell C or Vickers. A reading outside 22–32 HRC (d ≤ 16 mm) points to a heat-treatment problem even before tensile results come in. ISO 898-1 also covers surface checks, such as decarburisation and carburisation, which are assessed with low-load Vickers measurements.

What equipment does a fastener QC lab need?

Universal testing machine capacity

Size the UTM from the largest bolt you test. For example, an M24 class 8.8 bolt has As = 353 mm², so its minimum ultimate load is 830 MPa × 353 mm² ≈ 293 kN. Choose a capacity that keeps your highest expected loads inside the machine's verified range under IS 1828-1 / ISO 7500-1, with margin for stronger-than-minimum bolts. Akuracy's hydraulic grips universal testing machine is listed with a 100 kN to 1200 kN capacity range and an open-type crosshead with hydraulic wedge-action grips. You can see more models in the tensile testing machine range.

Fixtures

Plan for threaded adapters or nut fixtures for each thread size, wedge washers for the head-angle test, and hardened adapters that do not deform before the bolt does.

Hardness tester

For routine HRC checks, the digital Rockwell hardness tester supports Rockwell scales A, B and C with test loads of 60, 100 and 150 kgf. Compare options in the Rockwell hardness tester collection.

Common reasons 8.8 bolt tests fail (and how to avoid them)

  • Wrong stress area: use As for the actual thread (coarse or fine), not the shank area.
  • Too little thread engagement in the adapter: the adapter strips first and the bolt is wrongly rejected.
  • Misalignment: off-axis loading adds bending and lowers the breaking load.
  • Proof load overshoot: a ramp that is too fast or poor control stretches good bolts.
  • Hardness on an unprepared surface: scale, plating or a curved surface skews HRC readings.
  • Uncalibrated equipment: keep current calibration records for the UTM and hardness tester.

Where this matters in industry

Automotive and two-wheeler fastener suppliers test 8.8 bolts for PPAP and lot release. Structural steel fabricators and OEMs run incoming inspection on bought-in bolts. Third-party mechanical testing labs issue test reports against ISO 898-1 or IS 1367. In each case, the buyer wants the tensile, proof load and hardness results on one traceable report.

FAQ

What is the tensile strength of an 8.8 grade bolt?

The nominal tensile strength is 800 MPa. Under ISO 898-1, the minimum is 800 MPa for diameters up to 16 mm and 830 MPa above 16 mm.

What is the yield strength of an 8.8 grade bolt?

The nominal yield strength is 640 MPa (0.8 × 800). The minimum 0.2% proof strength is 640 MPa up to 16 mm and 660 MPa above 16 mm.

What is the hardness of an 8.8 grade bolt in HRC?

22–32 HRC for d ≤ 16 mm and 23–34 HRC for d > 16 mm, per ISO 898-1.

How is the proof load of a bolt calculated?

Proof load = proof stress (Sp) × nominal stress area (As). For an M12 class 8.8 bolt, that is 580 MPa × 84.3 mm² ≈ 48.9 kN.

Can one UTM do both tensile and proof load tests?

Yes. Both tests apply axial tension. You need suitable fixtures and a capacity that covers your largest bolt, and the proof load test also needs controlled loading and precise length measurement.

Request a Techno-Commercial Quotation

Setting up or upgrading a fastener testing lab? Share your bolt sizes, property classes and the standards you test to, and we will suggest a suitable UTM, fixtures and hardness tester.

Request a Techno-Commercial Quotation →