Discover the Power of Durability, Stability and Precision From Akuracy , a brand fully owned by Ratnakar Enterprises Jointly With Balaji Industries.

We offer high-quality products with unbeatable Innovative technologies and flexibility.

Our commitment to excellence is unmatched. Enjoy the benefits of our top-notch products today!

Static vs Dynamic Unbalance: What Each Means for Rotor Balancing

Akuracy hard bearing dynamic balancing machine showing two-plane unbalance for a rotor

Ameet Kudche |

Short answer: static unbalance means the rotor's centre of mass is offset from its axis of rotation, so it can be detected without spinning and corrected with one weight in a single plane. Dynamic unbalance combines that offset with a "couple" that makes the rotor rock end to end when it spins. It only shows up under rotation and needs correction in two planes. A dynamic balancing machine measures both and tells the operator how much weight to add or remove, and where.

Akuracy hard bearing dynamic balancing machine showing two-plane unbalance for a rotor

The four types of unbalance

Balancing standards describe unbalance in terms of how the rotor's principal axis of inertia sits relative to its shaft axis. In shop terms there are four cases.

1. Static unbalance

The principal axis is parallel to the shaft axis but displaced from it. The heavy spot pulls the rotor round until it settles at the bottom, which is why a rotor resting on knife edges or low-friction rollers will always stop in the same position. A single correction mass, placed opposite the heavy spot in a plane through the centre of mass, removes it.

2. Couple unbalance

Two equal heavy spots sit at opposite ends of the rotor, 180° apart. The centre of mass stays on the axis, so the rotor passes a static check perfectly. When it spins, though, the two forces form a couple that rocks the rotor about its centre. The bearings at each end see vibration that is out of phase with each other. Correction needs two weights in two planes.

3. Quasi-static unbalance

This is a special case where the principal axis crosses the shaft axis at a point other than the centre of mass. It behaves like a static unbalance placed in an "off-centre" plane.

4. Dynamic unbalance

This is the general case and the one almost every real rotor has: a mix of static and couple unbalance. The principal axis is neither parallel to nor intersecting the shaft axis in a simple way. It needs two-plane correction.

Why speed makes unbalance matter

The force an unbalance produces rises with the square of speed: F = U × ω², where U is the unbalance (mass × radius) and ω is the angular speed in rad/s.

Worked example: a rotor with U = 100 g·mm (0.0001 kg·m) running at 3000 rpm has ω ≈ 314 rad/s. The rotating force is 0.0001 × 314² ≈ 9.9 N. Double the speed to 6000 rpm and the force quadruples to about 39.5 N. That is why a part that seems smooth at low speed can vibrate badly at its service speed, and why balancing tolerances are tied to operating speed.

Static vs dynamic balancing: the practical difference

Point Static (single-plane) balancing Dynamic (two-plane) balancing
What it corrects Centre-of-mass offset only Offset plus couple (rocking) unbalance
Correction planes One Two (sometimes more for long flexible rotors)
Can it be checked without rotation? Yes, on knife edges or rollers, though only roughly No, the couple only appears when spinning
Typical parts Narrow discs: pulleys, flywheels, thin fan wheels, grinding wheels Longer rotors: motor armatures, crankshafts, rolls, impellers with wide hubs, turbine rotors

A common shop rule of thumb is that single-plane correction is usually enough when a rotor is short compared with its diameter and the bearings are far apart. Longer rotors, or any rotor where the correction planes are far from the centre of mass, need two planes. Treat this as a starting point, not a rule. If two-plane readings show significant couple unbalance on a "disc" part, it needs two-plane correction.

How a dynamic balancing machine works

The rotor is supported on two bearing pedestals and spun, usually by belt drive or end drive through a universal joint. Sensors at each support pick up the force or vibration, and a reference sensor tracks the angular position. The electronics then separate the signal into the two correction planes the operator has defined, using the rotor's dimensions entered at setup (the distances between the planes and supports, and the correction radii). The output for each plane is an amount (in grams, or g·mm) and an angle.

Hard-bearing machines measure the force at stiff supports, so they can be calibrated once for the machine geometry. Soft-bearing machines measure displacement on flexible supports and usually need a calibration run for each new rotor type. Akuracy's hard bearing dynamic balancing machine lists real-time two-plane unbalance indication on digital meters. More models, including belt-drive and end-driven types, are in the balancing machine range and on the dynamic balancing machine page.

Common mistakes when choosing single-plane balancing

  • Static check only on a long rotor: the part passes on knife edges but vibrates in service because the couple was never measured.
  • Correction plane in the wrong place: a single weight added far from the centre of mass fixes the static reading but creates a new couple.
  • Ignoring assembly: a balanced fan wheel can be unbalanced again by an eccentric hub, keyway or set screw. Balance with the key fitted (or use a half-key convention) and agree on it with the customer.
  • No tolerance agreed: without a balance grade and permissible residual unbalance, "balanced" has no measurable meaning on a test report.

Where this matters in industry

Electric motor manufacturers balance armatures and rotors in two planes before assembly. Pump and blower makers balance impellers and fan wheels. Engine and compressor builders balance crankshafts, and rewinding and repair shops rebalance rotors after rework. In each case the customer increasingly expects a balancing report that states the grade, the speed and the residual unbalance in each plane.

FAQ

What is the difference between static and dynamic balancing?

Static balancing corrects only the offset of the centre of mass, in one plane. Dynamic balancing corrects both that offset and the couple that makes a rotor rock end to end, using two correction planes while the rotor spins.

Can a rotor be statically balanced but dynamically unbalanced?

Yes. A rotor with pure couple unbalance has its centre of mass on the axis, so it passes a static check, but it still vibrates when it rotates.

When is single-plane balancing enough?

Usually for narrow, disc-shaped parts such as pulleys and thin fan wheels. If a two-plane measurement shows meaningful couple unbalance, switch to two-plane correction.

Why does unbalance get worse at higher speed?

The force from unbalance is proportional to the square of the speed, so doubling the speed multiplies the force by four.

What does a balancing machine display?

For each correction plane, the amount of unbalance and the angle at which to add or remove mass.

Request a Techno-Commercial Quotation

Tell us your rotor types, weights, diameters, service speeds and the balance grade your customers ask for, and we will suggest a suitable balancing machine configuration.

Request a Techno-Commercial Quotation →