Many components carry twisting loads: drive shafts, axles, bolts during tightening, springs and wires. A torsion test applies a twisting moment to a specimen and measures how it responds. It gives the shear properties of the material, which a tensile test cannot provide directly. This guide covers how torsion tests are set up and run, and how the results are calculated.
What a torsion test reveals
- Modulus of rigidity (shear modulus, G): the stiffness of the material in shear, from the elastic part of the torque-twist curve.
- Shear stress at the limit of proportionality or yield: where the curve departs from linear.
- Maximum torque and shear strength: the peak twisting capacity.
- Angle of twist or number of turns to failure: a measure of ductility in shear.
- Fracture appearance: ductile materials usually shear on a plane perpendicular to the axis; brittle materials tend to fail on a helical surface at about 45°.
Specimen set-up
- Measure the specimen: diameter at several points along the gauge length, and the gauge length itself.
- Grip both ends in the chucks so the specimen axis coincides with the machine axis. Misalignment introduces bending.
- Allow axial freedom: a specimen may shorten or lengthen slightly as it twists; many machines let one head move axially so no unwanted axial force develops.
- Attach a troptometer or angle sensor over the gauge length if you need accurate shear modulus, since twist measured at the chucks includes grip slip.
- Zero the torque and angle readings.
Running the test
Apply twist steadily, at a rate consistent with your standard or procedure, and record torque against angle of twist. In the elastic range take enough readings to define the straight line accurately. Continue to fracture if you need maximum torque and turns to failure.
Calculations for a solid circular shaft
For a solid round specimen of diameter d and gauge length L:
- Polar moment of inertia: J = π d4 / 32
- Shear stress at the surface: τ = T × (d/2) / J = 16 T / (π d3)
- Shear modulus: G = T × L / (J × θ), with θ the angle of twist in radians over the gauge length, taken from the elastic range
The shear stress formula assumes elastic behaviour; beyond yield, the stress distribution changes and the calculated "shear strength" at maximum torque is a nominal value, useful for comparison but not a true material stress. Hollow specimens use J = π (D4 − d4) / 32.
Wire twist (torsion) tests
For wire, a simpler test is common: the wire is gripped between two jaws at a specified distance and twisted in one direction until it breaks, counting the number of turns. The method for metallic wire is given in IS 1717 (corresponding to ISO 7800). The product standard specifies the free length, the speed and the minimum number of turns. The test reveals surface defects, seams and poor ductility, which show up as early failure or an irregular fracture.
| Test type | Main output | Typical use |
|---|---|---|
| Torque-twist test | G, shear stress, maximum torque | Material characterisation, shafts, research |
| Wire twist test | Number of turns to fracture | Wire production and acceptance |
| Component torsion test | Torque at failure or at a set angle | Fasteners, shafts, couplings |
Analog and digital torsion testers
Analog torsion machines show torque on a dial and twist on a graduated scale, which suits teaching labs. Digital machines record torque and angle electronically and can plot the curve and calculate results. Akuracy lists a torsion testing machine and a digital torsion testing machine RTT-60D; browse the torsion testing machine collection. Share your specimen sizes and the maximum torque you expect when you ask for a quote.
Common errors
- Measuring twist at the chucks when grips slip
- Specimen misaligned in the chucks
- Axial restraint causing unwanted tension or compression
- Using the elastic formula to report post-yield stress as a material property
Safety and specimen handling
Torsion specimens store elastic energy and can whip or throw fragments at fracture, particularly long wires. Use guards, keep hands clear of the chucks while the machine is running and release the torque before removing a specimen that did not break.
Key takeaways
- Align the specimen and allow axial freedom.
- Measure twist over the gauge length for accurate shear modulus.
- Post-yield shear stress from the elastic formula is a nominal value.
- Wire twist tests to IS 1717 count turns to fracture.
With careful set-up, correct twist measurement and clear reporting, a torsion test gives shear properties that complement tensile results and help predict how shafts, wires and fasteners behave in service.
Frequently asked questions
How is shear modulus calculated from a torsion test?
Use G = T L / (J θ) with torque and twist taken from the linear elastic part of the curve, θ in radians and twist measured over the gauge length.
Why do brittle materials break at 45°?
In torsion the maximum tensile stress acts at 45° to the axis. Brittle materials are weaker in tension than in shear, so they fracture along that helical plane.
What is a wire twist test used for?
It checks the ductility and surface quality of wire by counting turns to fracture, as specified in IS 1717 and product standards.
Request a quote
Akuracy (Ratnakar Enterprises) can advise on a configuration for your materials, standards and test volume. Share your specimen details and the standard you test to, and our team will reply with a suitable option. Request a quote online or message us on WhatsApp at +91 94038 91579.