Discover the Power of Durability, Stability and Precision From Akuracy , a brand fully owned by Ratnakar Enterprises Jointly With Balaji Industries.

We offer high-quality products with unbeatable Innovative technologies and flexibility.

Our commitment to excellence is unmatched. Enjoy the benefits of our top-notch products today!

How to prepare a Charpy V-notch specimen and perform the test

How to prepare a Charpy V-notch specimen and perform the test

Akuracy |

Written by
Akuracy
21 Nov 20268 min read

The charpy v notch specimen preparation and test procedure starts with identifying the governing test standard, then preparing and checking the notched specimen, conditioning it if required, verifying the machine, and recording the impact result. Follow the standard’s exact requirements for your material and test conditions; do not assume one specimen or setup fits every application.

Confirm the applicable standard and specimen requirements

Steel bars, calipers, micrometer, safety glasses, and a technical drawing

Start by identifying the standard and material specification that govern your Charpy V-notch impact test; these determine the specimen dimensions, notch geometry, test temperature, and machine requirements.

  1. Check the material specification, purchase requirements, or laboratory method to identify the applicable standard and its edition. Requirements can differ, so do not choose a specimen size or procedure based on an example intended for another material.
  2. Confirm whether the method calls for a full-size specimen or permits a reduced-size specimen. If a reduced size is needed because of material thickness or sample constraints, check the standard for the permitted dimensions and any reporting requirements.
  3. Find the specified specimen length, cross-section, notch depth, notch angle, notch-root radius, and tolerances. Also confirm how the notch must be oriented relative to the material’s rolling, forming, or other relevant direction.
  4. Check the required test temperature, conditioning method, and number of specimens. These details affect how specimens are prepared and handled, so settle them before machining or testing.

A Charpy V-notch specimen has a machined notch that concentrates stress at a defined location. During impact, the specimen breaks at or near that notch, allowing the test to measure energy absorbed during fracture under the specified conditions. The charpy v notch specimen preparation and test procedure is therefore tied to the material, specimen geometry, temperature, and test method—not just the impact tester.

Keep the selected standard and specimen drawing with the job record. If the application does not specify a method, ask the responsible materials or quality professional to determine which requirements apply before preparing specimens.

Charpy Impact Test | Laboratory Practical | Strength of Materials
▶ Charpy Impact Test | Laboratory Practical | Strength of Materials · YouTube

Prepare the specimen and machine the V-notch

Metal V-notch specimens beside a machining press and pointed tool

Prepare each specimen to the dimensions and notch geometry required by the selected standard, then inspect the machined notch before testing.

  1. Mark the specimen location and orientation on the source material before cutting. Preserve the direction information needed to relate the test result to the original material.
  2. Cut the blank to the required dimensions, leaving suitable allowance for finishing if the method requires it. Avoid introducing damage or distortion that could affect the final dimensions or fracture.
  3. Machine the V-notch using a suitable, controlled process. Use tooling appropriate to the specified notch geometry, and follow the standard’s requirements for the notch angle, depth, and root radius.
  4. Finish the specimen as required, keeping the notch and test surfaces free of burrs, unintended marks, or damage. Do not alter the notch by hand unless the method explicitly permits the technique.
  5. Measure the specimen dimensions and notch features with suitable measuring equipment. Record the actual measurements where required, and compare them with the applicable tolerances rather than relying on nominal settings alone.
  6. Identify each specimen so its source, orientation, preparation, and test result remain traceable.

A common preparation error is to machine the right-looking notch in the wrong orientation or to use dimensions from a different specimen type. Another is to record only the machine setting instead of checking the finished notch. For a charpy v-notch impact test, the specimen itself must meet the applicable method before the result can be interpreted against that method.

Condition the specimen at the required test temperature

Notched metal test specimens in an oven, tongs, and gloved hand

Condition specimens to the temperature specified by the applicable method, and transfer each one promptly so its temperature does not change beyond the method’s allowance.

  1. Confirm the target temperature and conditioning procedure in the test method or material specification. Do not substitute a convenient room-temperature test when the required condition is different.
  2. Use a temperature-control process suitable for the method and monitor the specimen condition as required. Follow the specified conditioning time and any requirements for the transfer interval.
  3. Keep specimens identified and organized so the correct sample is tested at the intended temperature. Avoid mixing conditioned and unconditioned specimens.
  4. Transfer one specimen at a time to the machine when that is necessary to limit temperature change. Arrange the work area and tools beforehand to avoid delays between removal from conditioning and impact.

Record the target temperature, actual temperature information required by the method, conditioning details, and relevant times. If the method specifies limits for timing or temperature variation, document how the test stayed within them. This record helps distinguish a material response from a test conducted under different conditions.

Verify the Charpy machine before testing

Hand placing a metal specimen in a Charpy impact tester

Check the machine, supports, anvils, striker, alignment, and verification records before use; suitability depends on documented compliance with the test method that applies to your work.

  1. Confirm the machine’s identification and capacity are suitable for the planned test, using its documentation and the requirements of the selected standard.
  2. Inspect the pendulum, striker, supports, anvils, guards, and other relevant components for damage, looseness, contamination, or visible wear. Compare the arrangement with the machine instructions and the required setup.
  3. Check that the striker and specimen supports are the correct configuration for the method. Verify their positioning and alignment using the applicable procedure; do not infer alignment from appearance alone.
  4. Review the machine’s current verification or calibration records and confirm they cover the relevant test configuration and requirements. A record for a different setup may not establish suitability for the planned test.
  5. Confirm that the result-reading system and any recording software are functioning as intended. If the test requires specific records, determine before testing how those values will be captured.
  6. Keep the inspection and verification evidence with the test documentation, including any machine checks required by the laboratory procedure.

A Charpy testing machine should be assessed against the requirements that govern the actual test—not a general label such as “impact tester.” If you are evaluating equipment, request the relevant machine documentation, verification records, setup details, and instructions for the intended specimen and method. Our Charpy Impact Testing Machine page identifies the equipment offering; confirm the configuration and documentation needed for your application before selecting a machine.

Position the specimen and perform the impact test

Place the specimen on the supports in the orientation required by the method, confirm the notch faces the correct direction, and operate the pendulum using the machine’s prescribed procedure.

  1. Confirm the specimen identity and required temperature before loading it. Match the specimen to its preparation and conditioning record.
  2. Place it on the supports at the specified position. For a Charpy V-notch arrangement, the notch is positioned in relation to the striker as directed by the applicable method; verify the orientation against the machine setup and method rather than relying on memory.
  3. Check that the specimen is seated correctly and that no support, fixture, or handling tool interferes with the impact path.
  4. Ensure the machine’s safety provisions are in place and follow its operating instructions. Clear the impact area and use the release procedure specified for that machine.
  5. Release the pendulum and allow the test cycle to complete. Do not handle the specimen or enter the impact area until the machine has stopped and the procedure permits access.
  6. Confirm that the machine has captured the result and that the specimen fractured as expected for the method. If the specimen slips, the impact is obstructed, or the recorded result is missing, document the event and follow the laboratory’s procedure for an invalid or repeated test.

Do not change the setup between specimens without recording and checking the change. Correct positioning is part of the charpy v notch impact testing procedure: a result from a misoriented or poorly seated specimen may not be comparable with results produced using the required arrangement.

Record the result and decide what to do next

Record the absorbed impact energy alongside specimen identity, dimensions, orientation, temperature, machine identification, and any required verification details.

  1. Capture the impact energy shown by the machine in the units and format required by the method. Do not convert or normalize the value unless the applicable procedure calls for it.
  2. Record specimen dimensions, notch details, material identification, orientation, and test temperature as required. Link every result to the correct specimen.
  3. Include the machine identification, relevant setup, verification status, operator, date, and any deviations or interruptions required by your laboratory records.
  4. Describe the fracture appearance only when the method or reporting procedure requires it, and use the specified terminology. Keep observations separate from the measured energy value.
  5. Compare results with acceptance limits only when those limits are stated in the applicable material specification, contract, or test plan. A Charpy result by itself does not establish pass or fail without the relevant criteria.

The absorbed impact energy indicates the energy associated with breaking the specimen under the recorded test conditions. It is not a universal acceptance threshold: interpretation depends on the governing requirements, including material, specimen type, orientation, and temperature.

Before future tests, confirm whether the existing machine setup, verification evidence, and specimen-preparation controls cover the required method. If not, identify the specific gap—such as specimen geometry, support arrangement, temperature handling, or records—and resolve it before reporting results as compliant.

Charpy Testing FAQ

These quick answers clarify common questions, but the applicable standard and material requirements still govern the specimen and procedure.

How is the Charpy impact test done?

A notched specimen is placed on machine supports in the required orientation, then struck by a pendulum; the machine records the energy absorbed during fracture. Follow the governing method for specimen, temperature, setup, and reporting.

What is the notch angle of an Izod impact test specimen?

The notch angle is specified by the applicable Izod method and specimen requirements; do not use a Charpy specimen drawing as a substitute. Check the governing standard before machining.

What is the ASTM standard for impact testing?

There is no single ASTM standard for every impact test; the appropriate method depends on the material, specimen, and test type. Identify the method named in the material specification or test plan.

What is a Charpy V-notch?

A Charpy V-notch is a machined V-shaped notch in a test specimen that localizes fracture during a pendulum impact test. Its geometry and orientation must follow the applicable method.

What are the two types of impact testing?

Charpy and Izod are two common pendulum impact-test methods. Their specimen support and orientation arrangements differ, so use the method specified for the material and application.

To move from preparation to a defensible test result, document the method and equipment requirements before cutting specimens or starting the machine.

  1. Identify the material specification and test method that apply to your intended Charpy V-notch test.
  2. Create a specimen drawing that includes the required dimensions, notch geometry, and material orientation.
  3. Confirm the conditioning procedure, target temperature, and records required by the method.
  4. Review the Charpy machine’s setup instructions, verification evidence, and required configuration against the selected method.
  5. Prepare and identify specimens, then record each test result with the associated specimen and machine details.
  6. Compare results only with acceptance criteria stated in the relevant specification or test plan.